/* [<][>][^][v][top][bottom][index][help] */
DEFINITIONS
This source file includes following definitions.
- native_sched_clock
- sched_clock
- check_tsc_unstable
- notsc_setup
- notsc_setup
- tsc_read_refs
- calc_hpet_ref
- calc_pmtimer_ref
- pit_calibrate_tsc
- pit_expect_msb
- quick_pit_calibrate
- native_calibrate_tsc
- recalibrate_cpu_khz
- set_cyc2ns_scale
- time_cpufreq_notifier
- cpufreq_tsc
- read_tsc
- vread_tsc
- mark_tsc_unstable
- dmi_mark_tsc_unstable
- check_geode_tsc_reliable
- check_geode_tsc_reliable
- unsynchronized_tsc
- init_tsc_clocksource
- tsc_init
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/timer.h>
#include <linux/acpi_pmtmr.h>
#include <linux/cpufreq.h>
#include <linux/dmi.h>
#include <linux/delay.h>
#include <linux/clocksource.h>
#include <linux/percpu.h>
#include <asm/hpet.h>
#include <asm/timer.h>
#include <asm/vgtod.h>
#include <asm/time.h>
#include <asm/delay.h>
unsigned int cpu_khz; /* TSC clocks / usec, not used here */
EXPORT_SYMBOL(cpu_khz);
unsigned int tsc_khz;
EXPORT_SYMBOL(tsc_khz);
/*
* TSC can be unstable due to cpufreq or due to unsynced TSCs
*/
static int tsc_unstable;
/* native_sched_clock() is called before tsc_init(), so
we must start with the TSC soft disabled to prevent
erroneous rdtsc usage on !cpu_has_tsc processors */
static int tsc_disabled = -1;
/*
* Scheduler clock - returns current time in nanosec units.
*/
u64 native_sched_clock(void)
{
u64 this_offset;
/*
* Fall back to jiffies if there's no TSC available:
* ( But note that we still use it if the TSC is marked
* unstable. We do this because unlike Time Of Day,
* the scheduler clock tolerates small errors and it's
* very important for it to be as fast as the platform
* can achive it. )
*/
if (unlikely(tsc_disabled)) {
/* No locking but a rare wrong value is not a big deal: */
return (jiffies_64 - INITIAL_JIFFIES) * (1000000000 / HZ);
}
/* read the Time Stamp Counter: */
rdtscll(this_offset);
/* return the value in ns */
return cycles_2_ns(this_offset);
}
/* We need to define a real function for sched_clock, to override the
weak default version */
#ifdef CONFIG_PARAVIRT
unsigned long long sched_clock(void)
{
return paravirt_sched_clock();
}
#else
unsigned long long
sched_clock(void) __attribute__((alias("native_sched_clock")));
#endif
int check_tsc_unstable(void)
{
return tsc_unstable;
}
EXPORT_SYMBOL_GPL(check_tsc_unstable);
#ifdef CONFIG_X86_TSC
int __init notsc_setup(char *str)
{
printk(KERN_WARNING "notsc: Kernel compiled with CONFIG_X86_TSC, "
"cannot disable TSC completely.\n");
tsc_disabled = 1;
return 1;
}
#else
/*
* disable flag for tsc. Takes effect by clearing the TSC cpu flag
* in cpu/common.c
*/
int __init notsc_setup(char *str)
{
setup_clear_cpu_cap(X86_FEATURE_TSC);
return 1;
}
#endif
__setup("notsc", notsc_setup);
#define MAX_RETRIES 5
#define SMI_TRESHOLD 50000
/*
* Read TSC and the reference counters. Take care of SMI disturbance
*/
static u64 tsc_read_refs(u64 *p, int hpet)
{
u64 t1, t2;
int i;
for (i = 0; i < MAX_RETRIES; i++) {
t1 = get_cycles();
if (hpet)
*p = hpet_readl(HPET_COUNTER) & 0xFFFFFFFF;
else
*p = acpi_pm_read_early();
t2 = get_cycles();
if ((t2 - t1) < SMI_TRESHOLD)
return t2;
}
return ULLONG_MAX;
}
/*
* Calculate the TSC frequency from HPET reference
*/
static unsigned long calc_hpet_ref(u64 deltatsc, u64 hpet1, u64 hpet2)
{
u64 tmp;
if (hpet2 < hpet1)
hpet2 += 0x100000000ULL;
hpet2 -= hpet1;
tmp = ((u64)hpet2 * hpet_readl(HPET_PERIOD));
do_div(tmp, 1000000);
do_div(deltatsc, tmp);
return (unsigned long) deltatsc;
}
/*
* Calculate the TSC frequency from PMTimer reference
*/
static unsigned long calc_pmtimer_ref(u64 deltatsc, u64 pm1, u64 pm2)
{
u64 tmp;
if (!pm1 && !pm2)
return ULONG_MAX;
if (pm2 < pm1)
pm2 += (u64)ACPI_PM_OVRRUN;
pm2 -= pm1;
tmp = pm2 * 1000000000LL;
do_div(tmp, PMTMR_TICKS_PER_SEC);
do_div(deltatsc, tmp);
return (unsigned long) deltatsc;
}
#define CAL_MS 10
#define CAL_LATCH (CLOCK_TICK_RATE / (1000 / CAL_MS))
#define CAL_PIT_LOOPS 1000
#define CAL2_MS 50
#define CAL2_LATCH (CLOCK_TICK_RATE / (1000 / CAL2_MS))
#define CAL2_PIT_LOOPS 5000
/*
* Try to calibrate the TSC against the Programmable
* Interrupt Timer and return the frequency of the TSC
* in kHz.
*
* Return ULONG_MAX on failure to calibrate.
*/
static unsigned long pit_calibrate_tsc(u32 latch, unsigned long ms, int loopmin)
{
u64 tsc, t1, t2, delta;
unsigned long tscmin, tscmax;
int pitcnt;
/* Set the Gate high, disable speaker */
outb((inb(0x61) & ~0x02) | 0x01, 0x61);
/*
* Setup CTC channel 2* for mode 0, (interrupt on terminal
* count mode), binary count. Set the latch register to 50ms
* (LSB then MSB) to begin countdown.
*/
outb(0xb0, 0x43);
outb(latch & 0xff, 0x42);
outb(latch >> 8, 0x42);
tsc = t1 = t2 = get_cycles();
pitcnt = 0;
tscmax = 0;
tscmin = ULONG_MAX;
while ((inb(0x61) & 0x20) == 0) {
t2 = get_cycles();
delta = t2 - tsc;
tsc = t2;
if ((unsigned long) delta < tscmin)
tscmin = (unsigned int) delta;
if ((unsigned long) delta > tscmax)
tscmax = (unsigned int) delta;
pitcnt++;
}
/*
* Sanity checks:
*
* If we were not able to read the PIT more than loopmin
* times, then we have been hit by a massive SMI
*
* If the maximum is 10 times larger than the minimum,
* then we got hit by an SMI as well.
*/
if (pitcnt < loopmin || tscmax > 10 * tscmin)
return ULONG_MAX;
/* Calculate the PIT value */
delta = t2 - t1;
do_div(delta, ms);
return delta;
}
/*
* This reads the current MSB of the PIT counter, and
* checks if we are running on sufficiently fast and
* non-virtualized hardware.
*
* Our expectations are:
*
* - the PIT is running at roughly 1.19MHz
*
* - each IO is going to take about 1us on real hardware,
* but we allow it to be much faster (by a factor of 10) or
* _slightly_ slower (ie we allow up to a 2us read+counter
* update - anything else implies a unacceptably slow CPU
* or PIT for the fast calibration to work.
*
* - with 256 PIT ticks to read the value, we have 214us to
* see the same MSB (and overhead like doing a single TSC
* read per MSB value etc).
*
* - We're doing 2 reads per loop (LSB, MSB), and we expect
* them each to take about a microsecond on real hardware.
* So we expect a count value of around 100. But we'll be
* generous, and accept anything over 50.
*
* - if the PIT is stuck, and we see *many* more reads, we
* return early (and the next caller of pit_expect_msb()
* then consider it a failure when they don't see the
* next expected value).
*
* These expectations mean that we know that we have seen the
* transition from one expected value to another with a fairly
* high accuracy, and we didn't miss any events. We can thus
* use the TSC value at the transitions to calculate a pretty
* good value for the TSC frequencty.
*/
static inline int pit_expect_msb(unsigned char val)
{
int count = 0;
for (count = 0; count < 50000; count++) {
/* Ignore LSB */
inb(0x42);
if (inb(0x42) != val)
break;
}
return count > 50;
}
/*
* How many MSB values do we want to see? We aim for a
* 15ms calibration, which assuming a 2us counter read
* error should give us roughly 150 ppm precision for
* the calibration.
*/
#define QUICK_PIT_MS 15
#define QUICK_PIT_ITERATIONS (QUICK_PIT_MS * PIT_TICK_RATE / 1000 / 256)
static unsigned long quick_pit_calibrate(void)
{
/* Set the Gate high, disable speaker */
outb((inb(0x61) & ~0x02) | 0x01, 0x61);
/*
* Counter 2, mode 0 (one-shot), binary count
*
* NOTE! Mode 2 decrements by two (and then the
* output is flipped each time, giving the same
* final output frequency as a decrement-by-one),
* so mode 0 is much better when looking at the
* individual counts.
*/
outb(0xb0, 0x43);
/* Start at 0xffff */
outb(0xff, 0x42);
outb(0xff, 0x42);
if (pit_expect_msb(0xff)) {
int i;
u64 t1, t2, delta;
unsigned char expect = 0xfe;
t1 = get_cycles();
for (i = 0; i < QUICK_PIT_ITERATIONS; i++, expect--) {
if (!pit_expect_msb(expect))
goto failed;
}
t2 = get_cycles();
/*
* Make sure we can rely on the second TSC timestamp:
*/
if (!pit_expect_msb(expect))
goto failed;
/*
* Ok, if we get here, then we've seen the
* MSB of the PIT decrement QUICK_PIT_ITERATIONS
* times, and each MSB had many hits, so we never
* had any sudden jumps.
*
* As a result, we can depend on there not being
* any odd delays anywhere, and the TSC reads are
* reliable.
*
* kHz = ticks / time-in-seconds / 1000;
* kHz = (t2 - t1) / (QPI * 256 / PIT_TICK_RATE) / 1000
* kHz = ((t2 - t1) * PIT_TICK_RATE) / (QPI * 256 * 1000)
*/
delta = (t2 - t1)*PIT_TICK_RATE;
do_div(delta, QUICK_PIT_ITERATIONS*256*1000);
printk("Fast TSC calibration using PIT\n");
return delta;
}
failed:
return 0;
}
/**
* native_calibrate_tsc - calibrate the tsc on boot
*/
unsigned long native_calibrate_tsc(void)
{
u64 tsc1, tsc2, delta, ref1, ref2;
unsigned long tsc_pit_min = ULONG_MAX, tsc_ref_min = ULONG_MAX;
unsigned long flags, latch, ms, fast_calibrate;
int hpet = is_hpet_enabled(), i, loopmin;
local_irq_save(flags);
fast_calibrate = quick_pit_calibrate();
local_irq_restore(flags);
if (fast_calibrate)
return fast_calibrate;
/*
* Run 5 calibration loops to get the lowest frequency value
* (the best estimate). We use two different calibration modes
* here:
*
* 1) PIT loop. We set the PIT Channel 2 to oneshot mode and
* load a timeout of 50ms. We read the time right after we
* started the timer and wait until the PIT count down reaches
* zero. In each wait loop iteration we read the TSC and check
* the delta to the previous read. We keep track of the min
* and max values of that delta. The delta is mostly defined
* by the IO time of the PIT access, so we can detect when a
* SMI/SMM disturbance happend between the two reads. If the
* maximum time is significantly larger than the minimum time,
* then we discard the result and have another try.
*
* 2) Reference counter. If available we use the HPET or the
* PMTIMER as a reference to check the sanity of that value.
* We use separate TSC readouts and check inside of the
* reference read for a SMI/SMM disturbance. We dicard
* disturbed values here as well. We do that around the PIT
* calibration delay loop as we have to wait for a certain
* amount of time anyway.
*/
/* Preset PIT loop values */
latch = CAL_LATCH;
ms = CAL_MS;
loopmin = CAL_PIT_LOOPS;
for (i = 0; i < 3; i++) {
unsigned long tsc_pit_khz;
/*
* Read the start value and the reference count of
* hpet/pmtimer when available. Then do the PIT
* calibration, which will take at least 50ms, and
* read the end value.
*/
local_irq_save(flags);
tsc1 = tsc_read_refs(&ref1, hpet);
tsc_pit_khz = pit_calibrate_tsc(latch, ms, loopmin);
tsc2 = tsc_read_refs(&ref2, hpet);
local_irq_restore(flags);
/* Pick the lowest PIT TSC calibration so far */
tsc_pit_min = min(tsc_pit_min, tsc_pit_khz);
/* hpet or pmtimer available ? */
if (!hpet && !ref1 && !ref2)
continue;
/* Check, whether the sampling was disturbed by an SMI */
if (tsc1 == ULLONG_MAX || tsc2 == ULLONG_MAX)
continue;
tsc2 = (tsc2 - tsc1) * 1000000LL;
if (hpet)
tsc2 = calc_hpet_ref(tsc2, ref1, ref2);
else
tsc2 = calc_pmtimer_ref(tsc2, ref1, ref2);
tsc_ref_min = min(tsc_ref_min, (unsigned long) tsc2);
/* Check the reference deviation */
delta = ((u64) tsc_pit_min) * 100;
do_div(delta, tsc_ref_min);
/*
* If both calibration results are inside a 10% window
* then we can be sure, that the calibration
* succeeded. We break out of the loop right away. We
* use the reference value, as it is more precise.
*/
if (delta >= 90 && delta <= 110) {
printk(KERN_INFO
"TSC: PIT calibration matches %s. %d loops\n",
hpet ? "HPET" : "PMTIMER", i + 1);
return tsc_ref_min;
}
/*
* Check whether PIT failed more than once. This
* happens in virtualized environments. We need to
* give the virtual PC a slightly longer timeframe for
* the HPET/PMTIMER to make the result precise.
*/
if (i == 1 && tsc_pit_min == ULONG_MAX) {
latch = CAL2_LATCH;
ms = CAL2_MS;
loopmin = CAL2_PIT_LOOPS;
}
}
/*
* Now check the results.
*/
if (tsc_pit_min == ULONG_MAX) {
/* PIT gave no useful value */
printk(KERN_WARNING "TSC: Unable to calibrate against PIT\n");
/* We don't have an alternative source, disable TSC */
if (!hpet && !ref1 && !ref2) {
printk("TSC: No reference (HPET/PMTIMER) available\n");
return 0;
}
/* The alternative source failed as well, disable TSC */
if (tsc_ref_min == ULONG_MAX) {
printk(KERN_WARNING "TSC: HPET/PMTIMER calibration "
"failed.\n");
return 0;
}
/* Use the alternative source */
printk(KERN_INFO "TSC: using %s reference calibration\n",
hpet ? "HPET" : "PMTIMER");
return tsc_ref_min;
}
/* We don't have an alternative source, use the PIT calibration value */
if (!hpet && !ref1 && !ref2) {
printk(KERN_INFO "TSC: Using PIT calibration value\n");
return tsc_pit_min;
}
/* The alternative source failed, use the PIT calibration value */
if (tsc_ref_min == ULONG_MAX) {
printk(KERN_WARNING "TSC: HPET/PMTIMER calibration failed. "
"Using PIT calibration\n");
return tsc_pit_min;
}
/*
* The calibration values differ too much. In doubt, we use
* the PIT value as we know that there are PMTIMERs around
* running at double speed. At least we let the user know:
*/
printk(KERN_WARNING "TSC: PIT calibration deviates from %s: %lu %lu.\n",
hpet ? "HPET" : "PMTIMER", tsc_pit_min, tsc_ref_min);
printk(KERN_INFO "TSC: Using PIT calibration value\n");
return tsc_pit_min;
}
#ifdef CONFIG_X86_32
/* Only called from the Powernow K7 cpu freq driver */
int recalibrate_cpu_khz(void)
{
#ifndef CONFIG_SMP
unsigned long cpu_khz_old = cpu_khz;
if (cpu_has_tsc) {
tsc_khz = calibrate_tsc();
cpu_khz = tsc_khz;
cpu_data(0).loops_per_jiffy =
cpufreq_scale(cpu_data(0).loops_per_jiffy,
cpu_khz_old, cpu_khz);
return 0;
} else
return -ENODEV;
#else
return -ENODEV;
#endif
}
EXPORT_SYMBOL(recalibrate_cpu_khz);
#endif /* CONFIG_X86_32 */
/* Accelerators for sched_clock()
* convert from cycles(64bits) => nanoseconds (64bits)
* basic equation:
* ns = cycles / (freq / ns_per_sec)
* ns = cycles * (ns_per_sec / freq)
* ns = cycles * (10^9 / (cpu_khz * 10^3))
* ns = cycles * (10^6 / cpu_khz)
*
* Then we use scaling math (suggested by george@mvista.com) to get:
* ns = cycles * (10^6 * SC / cpu_khz) / SC
* ns = cycles * cyc2ns_scale / SC
*
* And since SC is a constant power of two, we can convert the div
* into a shift.
*
* We can use khz divisor instead of mhz to keep a better precision, since
* cyc2ns_scale is limited to 10^6 * 2^10, which fits in 32 bits.
* (mathieu.desnoyers@polymtl.ca)
*
* -johnstul@us.ibm.com "math is hard, lets go shopping!"
*/
DEFINE_PER_CPU(unsigned long, cyc2ns);
static void set_cyc2ns_scale(unsigned long cpu_khz, int cpu)
{
unsigned long long tsc_now, ns_now;
unsigned long flags, *scale;
local_irq_save(flags);
sched_clock_idle_sleep_event();
scale = &per_cpu(cyc2ns, cpu);
rdtscll(tsc_now);
ns_now = __cycles_2_ns(tsc_now);
if (cpu_khz)
*scale = (NSEC_PER_MSEC << CYC2NS_SCALE_FACTOR)/cpu_khz;
sched_clock_idle_wakeup_event(0);
local_irq_restore(flags);
}
#ifdef CONFIG_CPU_FREQ
/* Frequency scaling support. Adjust the TSC based timer when the cpu frequency
* changes.
*
* RED-PEN: On SMP we assume all CPUs run with the same frequency. It's
* not that important because current Opteron setups do not support
* scaling on SMP anyroads.
*
* Should fix up last_tsc too. Currently gettimeofday in the
* first tick after the change will be slightly wrong.
*/
static unsigned int ref_freq;
static unsigned long loops_per_jiffy_ref;
static unsigned long tsc_khz_ref;
static int time_cpufreq_notifier(struct notifier_block *nb, unsigned long val,
void *data)
{
struct cpufreq_freqs *freq = data;
unsigned long *lpj, dummy;
if (cpu_has(&cpu_data(freq->cpu), X86_FEATURE_CONSTANT_TSC))
return 0;
lpj = &dummy;
if (!(freq->flags & CPUFREQ_CONST_LOOPS))
#ifdef CONFIG_SMP
lpj = &cpu_data(freq->cpu).loops_per_jiffy;
#else
lpj = &boot_cpu_data.loops_per_jiffy;
#endif
if (!ref_freq) {
ref_freq = freq->old;
loops_per_jiffy_ref = *lpj;
tsc_khz_ref = tsc_khz;
}
if ((val == CPUFREQ_PRECHANGE && freq->old < freq->new) ||
(val == CPUFREQ_POSTCHANGE && freq->old > freq->new) ||
(val == CPUFREQ_RESUMECHANGE)) {
*lpj = cpufreq_scale(loops_per_jiffy_ref, ref_freq, freq->new);
tsc_khz = cpufreq_scale(tsc_khz_ref, ref_freq, freq->new);
if (!(freq->flags & CPUFREQ_CONST_LOOPS))
mark_tsc_unstable("cpufreq changes");
}
set_cyc2ns_scale(tsc_khz, freq->cpu);
return 0;
}
static struct notifier_block time_cpufreq_notifier_block = {
.notifier_call = time_cpufreq_notifier
};
static int __init cpufreq_tsc(void)
{
if (!cpu_has_tsc)
return 0;
if (boot_cpu_has(X86_FEATURE_CONSTANT_TSC))
return 0;
cpufreq_register_notifier(&time_cpufreq_notifier_block,
CPUFREQ_TRANSITION_NOTIFIER);
return 0;
}
core_initcall(cpufreq_tsc);
#endif /* CONFIG_CPU_FREQ */
/* clocksource code */
static struct clocksource clocksource_tsc;
/*
* We compare the TSC to the cycle_last value in the clocksource
* structure to avoid a nasty time-warp. This can be observed in a
* very small window right after one CPU updated cycle_last under
* xtime/vsyscall_gtod lock and the other CPU reads a TSC value which
* is smaller than the cycle_last reference value due to a TSC which
* is slighty behind. This delta is nowhere else observable, but in
* that case it results in a forward time jump in the range of hours
* due to the unsigned delta calculation of the time keeping core
* code, which is necessary to support wrapping clocksources like pm
* timer.
*/
static cycle_t read_tsc(void)
{
cycle_t ret = (cycle_t)get_cycles();
return ret >= clocksource_tsc.cycle_last ?
ret : clocksource_tsc.cycle_last;
}
#ifdef CONFIG_X86_64
static cycle_t __vsyscall_fn vread_tsc(void)
{
cycle_t ret = (cycle_t)vget_cycles();
return ret >= __vsyscall_gtod_data.clock.cycle_last ?
ret : __vsyscall_gtod_data.clock.cycle_last;
}
#endif
static struct clocksource clocksource_tsc = {
.name = "tsc",
.rating = 300,
.read = read_tsc,
.mask = CLOCKSOURCE_MASK(64),
.shift = 22,
.flags = CLOCK_SOURCE_IS_CONTINUOUS |
CLOCK_SOURCE_MUST_VERIFY,
#ifdef CONFIG_X86_64
.vread = vread_tsc,
#endif
};
void mark_tsc_unstable(char *reason)
{
if (!tsc_unstable) {
tsc_unstable = 1;
printk("Marking TSC unstable due to %s\n", reason);
/* Change only the rating, when not registered */
if (clocksource_tsc.mult)
clocksource_change_rating(&clocksource_tsc, 0);
else
clocksource_tsc.rating = 0;
}
}
EXPORT_SYMBOL_GPL(mark_tsc_unstable);
static int __init dmi_mark_tsc_unstable(const struct dmi_system_id *d)
{
printk(KERN_NOTICE "%s detected: marking TSC unstable.\n",
d->ident);
tsc_unstable = 1;
return 0;
}
/* List of systems that have known TSC problems */
static struct dmi_system_id __initdata bad_tsc_dmi_table[] = {
{
.callback = dmi_mark_tsc_unstable,
.ident = "IBM Thinkpad 380XD",
.matches = {
DMI_MATCH(DMI_BOARD_VENDOR, "IBM"),
DMI_MATCH(DMI_BOARD_NAME, "2635FA0"),
},
},
{}
};
/*
* Geode_LX - the OLPC CPU has a possibly a very reliable TSC
*/
#ifdef CONFIG_MGEODE_LX
/* RTSC counts during suspend */
#define RTSC_SUSP 0x100
static void __init check_geode_tsc_reliable(void)
{
unsigned long res_low, res_high;
rdmsr_safe(MSR_GEODE_BUSCONT_CONF0, &res_low, &res_high);
if (res_low & RTSC_SUSP)
clocksource_tsc.flags &= ~CLOCK_SOURCE_MUST_VERIFY;
}
#else
static inline void check_geode_tsc_reliable(void) { }
#endif
/*
* Make an educated guess if the TSC is trustworthy and synchronized
* over all CPUs.
*/
__cpuinit int unsynchronized_tsc(void)
{
if (!cpu_has_tsc || tsc_unstable)
return 1;
#ifdef CONFIG_SMP
if (apic_is_clustered_box())
return 1;
#endif
if (boot_cpu_has(X86_FEATURE_CONSTANT_TSC))
return 0;
/*
* Intel systems are normally all synchronized.
* Exceptions must mark TSC as unstable:
*/
if (boot_cpu_data.x86_vendor != X86_VENDOR_INTEL) {
/* assume multi socket systems are not synchronized: */
if (num_possible_cpus() > 1)
tsc_unstable = 1;
}
return tsc_unstable;
}
static void __init init_tsc_clocksource(void)
{
clocksource_tsc.mult = clocksource_khz2mult(tsc_khz,
clocksource_tsc.shift);
/* lower the rating if we already know its unstable: */
if (check_tsc_unstable()) {
clocksource_tsc.rating = 0;
clocksource_tsc.flags &= ~CLOCK_SOURCE_IS_CONTINUOUS;
}
clocksource_register(&clocksource_tsc);
}
void __init tsc_init(void)
{
u64 lpj;
int cpu;
if (!cpu_has_tsc)
return;
tsc_khz = calibrate_tsc();
cpu_khz = tsc_khz;
if (!tsc_khz) {
mark_tsc_unstable("could not calculate TSC khz");
return;
}
#ifdef CONFIG_X86_64
if (cpu_has(&boot_cpu_data, X86_FEATURE_CONSTANT_TSC) &&
(boot_cpu_data.x86_vendor == X86_VENDOR_AMD))
cpu_khz = calibrate_cpu();
#endif
lpj = ((u64)tsc_khz * 1000);
do_div(lpj, HZ);
lpj_fine = lpj;
printk("Detected %lu.%03lu MHz processor.\n",
(unsigned long)cpu_khz / 1000,
(unsigned long)cpu_khz % 1000);
/*
* Secondary CPUs do not run through tsc_init(), so set up
* all the scale factors for all CPUs, assuming the same
* speed as the bootup CPU. (cpufreq notifiers will fix this
* up if their speed diverges)
*/
for_each_possible_cpu(cpu)
set_cyc2ns_scale(cpu_khz, cpu);
if (tsc_disabled > 0)
return;
/* now allow native_sched_clock() to use rdtsc */
tsc_disabled = 0;
use_tsc_delay();
/* Check and install the TSC clocksource */
dmi_check_system(bad_tsc_dmi_table);
if (unsynchronized_tsc())
mark_tsc_unstable("TSCs unsynchronized");
check_geode_tsc_reliable();
init_tsc_clocksource();
}