[funini.com] -> [kei@sodan] -> Kernel Reading

root/sound/oss/sb_common.c

/* [<][>][^][v][top][bottom][index][help] */

DEFINITIONS

This source file includes following definitions.
  1. sb_dsp_command
  2. sb_dsp_get_byte
  3. sb_intr
  4. pci_intr
  5. sbintr
  6. sb_dsp_reset
  7. dsp_get_vers
  8. sb16_set_dma_hw
  9. sb16_set_mpu_port
  10. sb16_set_irq_hw
  11. relocate_Jazz16
  12. init_Jazz16
  13. relocate_ess1688
  14. sb_dsp_detect
  15. sb_dsp_init
  16. sb_dsp_unload
  17. sb_setmixer
  18. sb_getmixer
  19. smw_putmem
  20. smw_getmem
  21. smw_midi_init
  22. init_Jazz16_midi
  23. probe_sbmpu
  24. unload_sbmpu

/*
 * sound/oss/sb_common.c
 *
 * Common routines for Sound Blaster compatible cards.
 *
 *
 * Copyright (C) by Hannu Savolainen 1993-1997
 *
 * OSS/Free for Linux is distributed under the GNU GENERAL PUBLIC LICENSE (GPL)
 * Version 2 (June 1991). See the "COPYING" file distributed with this software
 * for more info.
 *
 *
 * Daniel J. Rodriksson: Modified sbintr to handle 8 and 16 bit interrupts
 *                       for full duplex support ( only sb16 by now )
 * Rolf Fokkens:         Added (BETA?) support for ES1887 chips.
 * (fokkensr@vertis.nl)  Which means: You can adjust the recording levels.
 *
 * 2000/01/18 - separated sb_card and sb_common -
 * Jeff Garzik <jgarzik@pobox.com>
 *
 * 2000/09/18 - got rid of attach_uart401
 * Arnaldo Carvalho de Melo <acme@conectiva.com.br>
 *
 * 2001/01/26 - replaced CLI/STI with spinlocks
 * Chris Rankin <rankinc@zipworld.com.au>
 */

#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/spinlock.h>

#include "sound_config.h"
#include "sound_firmware.h"

#include "mpu401.h"

#include "sb_mixer.h"
#include "sb.h"
#include "sb_ess.h"

/*
 * global module flag
 */

int sb_be_quiet;

static sb_devc *detected_devc;  /* For communication from probe to init */
static sb_devc *last_devc;      /* For MPU401 initialization */

static unsigned char jazz_irq_bits[] = {
        0, 0, 2, 3, 0, 1, 0, 4, 0, 2, 5, 0, 0, 0, 0, 6
};

static unsigned char jazz_dma_bits[] = {
        0, 1, 0, 2, 0, 3, 0, 4
};

void *smw_free;

/*
 * Jazz16 chipset specific control variables
 */

static int jazz16_base;                 /* Not detected */
static unsigned char jazz16_bits;       /* I/O relocation bits */
static DEFINE_SPINLOCK(jazz16_lock);

/*
 * Logitech Soundman Wave specific initialization code
 */

#ifdef SMW_MIDI0001_INCLUDED
#include "smw-midi0001.h"
#else
static unsigned char *smw_ucode;
static int      smw_ucodeLen;

#endif

static sb_devc *last_sb;                /* Last sb loaded */

int sb_dsp_command(sb_devc * devc, unsigned char val)
{
        int i;
        unsigned long limit;

        limit = jiffies + HZ / 10;      /* Timeout */
        
        /*
         * Note! the i<500000 is an emergency exit. The sb_dsp_command() is sometimes
         * called while interrupts are disabled. This means that the timer is
         * disabled also. However the timeout situation is a abnormal condition.
         * Normally the DSP should be ready to accept commands after just couple of
         * loops.
         */

        for (i = 0; i < 500000 && (limit-jiffies)>0; i++)
        {
                if ((inb(DSP_STATUS) & 0x80) == 0)
                {
                        outb((val), DSP_COMMAND);
                        return 1;
                }
        }
        printk(KERN_WARNING "Sound Blaster:  DSP command(%x) timeout.\n", val);
        return 0;
}

int sb_dsp_get_byte(sb_devc * devc)
{
        int i;

        for (i = 1000; i; i--)
        {
                if (inb(DSP_DATA_AVAIL) & 0x80)
                        return inb(DSP_READ);
        }
        return 0xffff;
}

static void sb_intr (sb_devc *devc)
{
        int status;
        unsigned char   src = 0xff;

        if (devc->model == MDL_SB16)
        {
                src = sb_getmixer(devc, IRQ_STAT);      /* Interrupt source register */

                if (src & 4)                                            /* MPU401 interrupt */
                        if(devc->midi_irq_cookie)
                                uart401intr(devc->irq, devc->midi_irq_cookie);

                if (!(src & 3))
                        return; /* Not a DSP interrupt */
        }
        if (devc->intr_active && (!devc->fullduplex || (src & 0x01)))
        {
                switch (devc->irq_mode)
                {
                        case IMODE_OUTPUT:
                                DMAbuf_outputintr(devc->dev, 1);
                                break;

                        case IMODE_INPUT:
                                DMAbuf_inputintr(devc->dev);
                                break;

                        case IMODE_INIT:
                                break;

                        case IMODE_MIDI:
                                sb_midi_interrupt(devc);
                                break;

                        default:
                                /* printk(KERN_WARN "Sound Blaster: Unexpected interrupt\n"); */
                                ;
                }
        }
        else if (devc->intr_active_16 && (src & 0x02))
        {
                switch (devc->irq_mode_16)
                {
                        case IMODE_OUTPUT:
                                DMAbuf_outputintr(devc->dev, 1);
                                break;

                        case IMODE_INPUT:
                                DMAbuf_inputintr(devc->dev);
                                break;

                        case IMODE_INIT:
                                break;

                        default:
                                /* printk(KERN_WARN "Sound Blaster: Unexpected interrupt\n"); */
                                ;
                }
        }
        /*
         * Acknowledge interrupts 
         */

        if (src & 0x01)
                status = inb(DSP_DATA_AVAIL);

        if (devc->model == MDL_SB16 && src & 0x02)
                status = inb(DSP_DATA_AVL16);
}

static void pci_intr(sb_devc *devc)
{
        int src = inb(devc->pcibase+0x1A);
        src&=3;
        if(src)
                sb_intr(devc);
}

static irqreturn_t sbintr(int irq, void *dev_id)
{
        sb_devc *devc = dev_id;

        devc->irq_ok = 1;

        switch (devc->model) {
        case MDL_ESSPCI:
                pci_intr (devc);
                break;
                
        case MDL_ESS:
                ess_intr (devc);
                break;
        default:
                sb_intr (devc);
                break;
        }
        return IRQ_HANDLED;
}

int sb_dsp_reset(sb_devc * devc)
{
        int loopc;

        DEB(printk("Entered sb_dsp_reset()\n"));

        if (devc->model == MDL_ESS) return ess_dsp_reset (devc);

        /* This is only for non-ESS chips */

        outb(1, DSP_RESET);

        udelay(10);
        outb(0, DSP_RESET);
        udelay(30);

        for (loopc = 0; loopc < 1000 && !(inb(DSP_DATA_AVAIL) & 0x80); loopc++);

        if (inb(DSP_READ) != 0xAA)
        {
                DDB(printk("sb: No response to RESET\n"));
                return 0;       /* Sorry */
        }

        DEB(printk("sb_dsp_reset() OK\n"));

        return 1;
}

static void dsp_get_vers(sb_devc * devc)
{
        int i;

        unsigned long   flags;

        DDB(printk("Entered dsp_get_vers()\n"));
        spin_lock_irqsave(&devc->lock, flags);
        devc->major = devc->minor = 0;
        sb_dsp_command(devc, 0xe1);     /* Get version */

        for (i = 100000; i; i--)
        {
                if (inb(DSP_DATA_AVAIL) & 0x80)
                {
                        if (devc->major == 0)
                                devc->major = inb(DSP_READ);
                        else
                        {
                                devc->minor = inb(DSP_READ);
                                break;
                        }
                }
        }
        spin_unlock_irqrestore(&devc->lock, flags);
        DDB(printk("DSP version %d.%02d\n", devc->major, devc->minor));
}

static int sb16_set_dma_hw(sb_devc * devc)
{
        int bits;

        if (devc->dma8 != 0 && devc->dma8 != 1 && devc->dma8 != 3)
        {
                printk(KERN_ERR "SB16: Invalid 8 bit DMA (%d)\n", devc->dma8);
                return 0;
        }
        bits = (1 << devc->dma8);

        if (devc->dma16 >= 5 && devc->dma16 <= 7)
                bits |= (1 << devc->dma16);

        sb_setmixer(devc, DMA_NR, bits);
        return 1;
}

static void sb16_set_mpu_port(sb_devc * devc, struct address_info *hw_config)
{
        /*
         * This routine initializes new MIDI port setup register of SB Vibra (CT2502).
         */
        unsigned char   bits = sb_getmixer(devc, 0x84) & ~0x06;

        switch (hw_config->io_base)
        {
                case 0x300:
                        sb_setmixer(devc, 0x84, bits | 0x04);
                        break;

                case 0x330:
                        sb_setmixer(devc, 0x84, bits | 0x00);
                        break;

                default:
                        sb_setmixer(devc, 0x84, bits | 0x02);           /* Disable MPU */
                        printk(KERN_ERR "SB16: Invalid MIDI I/O port %x\n", hw_config->io_base);
        }
}

static int sb16_set_irq_hw(sb_devc * devc, int level)
{
        int ival;

        switch (level)
        {
                case 5:
                        ival = 2;
                        break;
                case 7:
                        ival = 4;
                        break;
                case 9:
                        ival = 1;
                        break;
                case 10:
                        ival = 8;
                        break;
                default:
                        printk(KERN_ERR "SB16: Invalid IRQ%d\n", level);
                        return 0;
        }
        sb_setmixer(devc, IRQ_NR, ival);
        return 1;
}

static void relocate_Jazz16(sb_devc * devc, struct address_info *hw_config)
{
        unsigned char bits = 0;
        unsigned long flags;

        if (jazz16_base != 0 && jazz16_base != hw_config->io_base)
                return;

        switch (hw_config->io_base)
        {
                case 0x220:
                        bits = 1;
                        break;
                case 0x240:
                        bits = 2;
                        break;
                case 0x260:
                        bits = 3;
                        break;
                default:
                        return;
        }
        bits = jazz16_bits = bits << 5;
        jazz16_base = hw_config->io_base;

        /*
         *      Magic wake up sequence by writing to 0x201 (aka Joystick port)
         */
        spin_lock_irqsave(&jazz16_lock, flags);
        outb((0xAF), 0x201);
        outb((0x50), 0x201);
        outb((bits), 0x201);
        spin_unlock_irqrestore(&jazz16_lock, flags);
}

static int init_Jazz16(sb_devc * devc, struct address_info *hw_config)
{
        char name[100];
        /*
         * First try to check that the card has Jazz16 chip. It identifies itself
         * by returning 0x12 as response to DSP command 0xfa.
         */

        if (!sb_dsp_command(devc, 0xfa))
                return 0;

        if (sb_dsp_get_byte(devc) != 0x12)
                return 0;

        /*
         * OK so far. Now configure the IRQ and DMA channel used by the card.
         */
        if (hw_config->irq < 1 || hw_config->irq > 15 || jazz_irq_bits[hw_config->irq] == 0)
        {
                printk(KERN_ERR "Jazz16: Invalid interrupt (IRQ%d)\n", hw_config->irq);
                return 0;
        }
        if (hw_config->dma < 0 || hw_config->dma > 3 || jazz_dma_bits[hw_config->dma] == 0)
        {
                  printk(KERN_ERR "Jazz16: Invalid 8 bit DMA (DMA%d)\n", hw_config->dma);
                  return 0;
        }
        if (hw_config->dma2 < 0)
        {
                printk(KERN_ERR "Jazz16: No 16 bit DMA channel defined\n");
                return 0;
        }
        if (hw_config->dma2 < 5 || hw_config->dma2 > 7 || jazz_dma_bits[hw_config->dma2] == 0)
        {
                printk(KERN_ERR "Jazz16: Invalid 16 bit DMA (DMA%d)\n", hw_config->dma2);
                return 0;
        }
        devc->dma16 = hw_config->dma2;

        if (!sb_dsp_command(devc, 0xfb))
                return 0;

        if (!sb_dsp_command(devc, jazz_dma_bits[hw_config->dma] |
                        (jazz_dma_bits[hw_config->dma2] << 4)))
                return 0;

        if (!sb_dsp_command(devc, jazz_irq_bits[hw_config->irq]))
                return 0;

        /*
         * Now we have configured a standard Jazz16 device. 
         */
        devc->model = MDL_JAZZ;
        strcpy(name, "Jazz16");

        hw_config->name = "Jazz16";
        devc->caps |= SB_NO_MIDI;
        return 1;
}

static void relocate_ess1688(sb_devc * devc)
{
        unsigned char bits;

        switch (devc->base)
        {
                case 0x220:
                        bits = 0x04;
                        break;
                case 0x230:
                        bits = 0x05;
                        break;
                case 0x240:
                        bits = 0x06;
                        break;
                case 0x250:
                        bits = 0x07;
                        break;
                default:
                        return; /* Wrong port */
        }

        DDB(printk("Doing ESS1688 address selection\n"));
        
        /*
         * ES1688 supports two alternative ways for software address config.
         * First try the so called Read-Sequence-Key method.
         */

        /* Reset the sequence logic */
        inb(0x229);
        inb(0x229);
        inb(0x229);

        /* Perform the read sequence */
        inb(0x22b);
        inb(0x229);
        inb(0x22b);
        inb(0x229);
        inb(0x229);
        inb(0x22b);
        inb(0x229);

        /* Select the base address by reading from it. Then probe using the port. */
        inb(devc->base);
        if (sb_dsp_reset(devc)) /* Bingo */
                return;

#if 0                           /* This causes system lockups (Nokia 386/25 at least) */
        /*
         * The last resort is the system control register method.
         */

        outb((0x00), 0xfb);     /* 0xFB is the unlock register */
        outb((0x00), 0xe0);     /* Select index 0 */
        outb((bits), 0xe1);     /* Write the config bits */
        outb((0x00), 0xf9);     /* 0xFB is the lock register */
#endif
}

int sb_dsp_detect(struct address_info *hw_config, int pci, int pciio, struct sb_module_options *sbmo)
{
        sb_devc sb_info;
        sb_devc *devc = &sb_info;

        memset((char *) &sb_info, 0, sizeof(sb_info));  /* Zero everything */

        /* Copy module options in place */
        if(sbmo) memcpy(&devc->sbmo, sbmo, sizeof(struct sb_module_options));

        sb_info.my_mididev = -1;
        sb_info.my_mixerdev = -1;
        sb_info.dev = -1;

        /*
         * Initialize variables 
         */
        
        DDB(printk("sb_dsp_detect(%x) entered\n", hw_config->io_base));

        spin_lock_init(&devc->lock);
        devc->type = hw_config->card_subtype;

        devc->base = hw_config->io_base;
        devc->irq = hw_config->irq;
        devc->dma8 = hw_config->dma;

        devc->dma16 = -1;
        devc->pcibase = pciio;
        
        if(pci == SB_PCI_ESSMAESTRO)
        {
                devc->model = MDL_ESSPCI;
                devc->caps |= SB_PCI_IRQ;
                hw_config->driver_use_1 |= SB_PCI_IRQ;
                hw_config->card_subtype = MDL_ESSPCI;
        }
        
        if(pci == SB_PCI_YAMAHA)
        {
                devc->model = MDL_YMPCI;
                devc->caps |= SB_PCI_IRQ;
                hw_config->driver_use_1 |= SB_PCI_IRQ;
                hw_config->card_subtype = MDL_YMPCI;
                
                printk("Yamaha PCI mode.\n");
        }
        
        if (devc->sbmo.acer)
        {
                unsigned long flags;

                spin_lock_irqsave(&devc->lock, flags);
                inb(devc->base + 0x09);
                inb(devc->base + 0x09);
                inb(devc->base + 0x09);
                inb(devc->base + 0x0b);
                inb(devc->base + 0x09);
                inb(devc->base + 0x0b);
                inb(devc->base + 0x09);
                inb(devc->base + 0x09);
                inb(devc->base + 0x0b);
                inb(devc->base + 0x09);
                inb(devc->base + 0x00);
                spin_unlock_irqrestore(&devc->lock, flags);
        }
        /*
         * Detect the device
         */

        if (sb_dsp_reset(devc))
                dsp_get_vers(devc);
        else
                devc->major = 0;

        if (devc->type == 0 || devc->type == MDL_JAZZ || devc->type == MDL_SMW)
                if (devc->major == 0 || (devc->major == 3 && devc->minor == 1))
                        relocate_Jazz16(devc, hw_config);

        if (devc->major == 0 && (devc->type == MDL_ESS || devc->type == 0))
                relocate_ess1688(devc);

        if (!sb_dsp_reset(devc))
        {
                DDB(printk("SB reset failed\n"));
#ifdef MODULE
                printk(KERN_INFO "sb: dsp reset failed.\n");
#endif
                return 0;
        }
        if (devc->major == 0)
                dsp_get_vers(devc);

        if (devc->major == 3 && devc->minor == 1)
        {
                if (devc->type == MDL_AZTECH)           /* SG Washington? */
                {
                        if (sb_dsp_command(devc, 0x09))
                                if (sb_dsp_command(devc, 0x00)) /* Enter WSS mode */
                                {
                                        int i;

                                        /* Have some delay */
                                        for (i = 0; i < 10000; i++)
                                                inb(DSP_DATA_AVAIL);
                                        devc->caps = SB_NO_AUDIO | SB_NO_MIDI;  /* Mixer only */
                                        devc->model = MDL_AZTECH;
                                }
                }
        }
        
        if(devc->type == MDL_ESSPCI)
                devc->model = MDL_ESSPCI;
                
        if(devc->type == MDL_YMPCI)
        {
                printk("YMPCI selected\n");
                devc->model = MDL_YMPCI;
        }
                
        /*
         * Save device information for sb_dsp_init()
         */


        detected_devc = kmalloc(sizeof(sb_devc), GFP_KERNEL);
        if (detected_devc == NULL)
        {
                printk(KERN_ERR "sb: Can't allocate memory for device information\n");
                return 0;
        }
        memcpy(detected_devc, devc, sizeof(sb_devc));
        MDB(printk(KERN_INFO "SB %d.%02d detected OK (%x)\n", devc->major, devc->minor, hw_config->io_base));
        return 1;
}

int sb_dsp_init(struct address_info *hw_config, struct module *owner)
{
        sb_devc *devc;
        char name[100];
        extern int sb_be_quiet;
        int     mixer22, mixer30;
        
/*
 * Check if we had detected a SB device earlier
 */
        DDB(printk("sb_dsp_init(%x) entered\n", hw_config->io_base));
        name[0] = 0;

        if (detected_devc == NULL)
        {
                MDB(printk("No detected device\n"));
                return 0;
        }
        devc = detected_devc;
        detected_devc = NULL;

        if (devc->base != hw_config->io_base)
        {
                DDB(printk("I/O port mismatch\n"));
                release_region(devc->base, 16);
                return 0;
        }
        /*
         * Now continue initialization of the device
         */

        devc->caps = hw_config->driver_use_1;

        if (!((devc->caps & SB_NO_AUDIO) && (devc->caps & SB_NO_MIDI)) && hw_config->irq > 0)
        {                       /* IRQ setup */
                
                /*
                 *      ESS PCI cards do shared PCI IRQ stuff. Since they
                 *      will get shared PCI irq lines we must cope.
                 */
                 
                int i=(devc->caps&SB_PCI_IRQ)?IRQF_SHARED:0;
                
                if (request_irq(hw_config->irq, sbintr, i, "soundblaster", devc) < 0)
                {
                        printk(KERN_ERR "SB: Can't allocate IRQ%d\n", hw_config->irq);
                        release_region(devc->base, 16);
                        return 0;
                }
                devc->irq_ok = 0;

                if (devc->major == 4)
                        if (!sb16_set_irq_hw(devc, devc->irq))  /* Unsupported IRQ */
                        {
                                free_irq(devc->irq, devc);
                                release_region(devc->base, 16);
                                return 0;
                        }
                if ((devc->type == 0 || devc->type == MDL_ESS) &&
                        devc->major == 3 && devc->minor == 1)
                {               /* Handle various chipsets which claim they are SB Pro compatible */
                        if ((devc->type != 0 && devc->type != MDL_ESS) ||
                                !ess_init(devc, hw_config))
                        {
                                if ((devc->type != 0 && devc->type != MDL_JAZZ &&
                                         devc->type != MDL_SMW) || !init_Jazz16(devc, hw_config))
                                {
                                        DDB(printk("This is a genuine SB Pro\n"));
                                }
                        }
                }
                if (devc->major == 4 && devc->minor <= 11 )     /* Won't work */
                        devc->irq_ok = 1;
                else
                {
                        int n;

                        for (n = 0; n < 3 && devc->irq_ok == 0; n++)
                        {
                                if (sb_dsp_command(devc, 0xf2)) /* Cause interrupt immediately */
                                {
                                        int i;

                                        for (i = 0; !devc->irq_ok && i < 10000; i++);
                                }
                        }
                        if (!devc->irq_ok)
                                printk(KERN_WARNING "sb: Interrupt test on IRQ%d failed - Probable IRQ conflict\n", devc->irq);
                        else
                        {
                                DDB(printk("IRQ test OK (IRQ%d)\n", devc->irq));
                        }
                }
        }                       /* IRQ setup */

        last_sb = devc;
        
        switch (devc->major)
        {
                case 1:         /* SB 1.0 or 1.5 */
                        devc->model = hw_config->card_subtype = MDL_SB1;
                        break;

                case 2:         /* SB 2.x */
                        if (devc->minor == 0)
                                devc->model = hw_config->card_subtype = MDL_SB2;
                        else
                                devc->model = hw_config->card_subtype = MDL_SB201;
                        break;

                case 3:         /* SB Pro and most clones */
                        switch (devc->model) {
                        case 0:
                                devc->model = hw_config->card_subtype = MDL_SBPRO;
                                if (hw_config->name == NULL)
                                        hw_config->name = "Sound Blaster Pro (8 BIT ONLY)";
                                break;
                        case MDL_ESS:
                                ess_dsp_init(devc, hw_config);
                                break;
                        }
                        break;

                case 4:
                        devc->model = hw_config->card_subtype = MDL_SB16;
                        /* 
                         * ALS007 and ALS100 return DSP version 4.2 and have 2 post-reset !=0
                         * registers at 0x3c and 0x4c (output ctrl registers on ALS007) whereas
                         * a "standard" SB16 doesn't have a register at 0x4c.  ALS100 actively
                         * updates register 0x22 whenever 0x30 changes, as per the SB16 spec.
                         * Since ALS007 doesn't, this can be used to differentiate the 2 cards.
                         */
                        if ((devc->minor == 2) && sb_getmixer(devc,0x3c) && sb_getmixer(devc,0x4c)) 
                        {
                                mixer30 = sb_getmixer(devc,0x30);
                                sb_setmixer(devc,0x22,(mixer22=sb_getmixer(devc,0x22)) & 0x0f);
                                sb_setmixer(devc,0x30,0xff);
                                /* ALS100 will force 0x30 to 0xf8 like SB16; ALS007 will allow 0xff. */
                                /* Register 0x22 & 0xf0 on ALS100 == 0xf0; on ALS007 it == 0x10.     */
                                if ((sb_getmixer(devc,0x30) != 0xff) || ((sb_getmixer(devc,0x22) & 0xf0) != 0x10)) 
                                {
                                        devc->submodel = SUBMDL_ALS100;
                                        if (hw_config->name == NULL)
                                                hw_config->name = "Sound Blaster 16 (ALS-100)";
                                }
                                else
                                {
                                        sb_setmixer(devc,0x3c,0x1f);    /* Enable all inputs */
                                        sb_setmixer(devc,0x4c,0x1f);
                                        sb_setmixer(devc,0x22,mixer22); /* Restore 0x22 to original value */
                                        devc->submodel = SUBMDL_ALS007;
                                        if (hw_config->name == NULL)
                                                hw_config->name = "Sound Blaster 16 (ALS-007)";
                                }
                                sb_setmixer(devc,0x30,mixer30);
                        }
                        else if (hw_config->name == NULL)
                                hw_config->name = "Sound Blaster 16";

                        if (hw_config->dma2 == -1)
                                devc->dma16 = devc->dma8;
                        else if (hw_config->dma2 < 5 || hw_config->dma2 > 7)
                        {
                                printk(KERN_WARNING  "SB16: Bad or missing 16 bit DMA channel\n");
                                devc->dma16 = devc->dma8;
                        }
                        else
                                devc->dma16 = hw_config->dma2;

                        if(!sb16_set_dma_hw(devc)) {
                                free_irq(devc->irq, devc);
                                release_region(hw_config->io_base, 16);
                                return 0;
                        }

                        devc->caps |= SB_NO_MIDI;
        }

        if (!(devc->caps & SB_NO_MIXER))
                if (devc->major == 3 || devc->major == 4)
                        sb_mixer_init(devc, owner);

        if (!(devc->caps & SB_NO_MIDI))
                sb_dsp_midi_init(devc, owner);

        if (hw_config->name == NULL)
                hw_config->name = "Sound Blaster (8 BIT/MONO ONLY)";

        sprintf(name, "%s (%d.%02d)", hw_config->name, devc->major, devc->minor);
        conf_printf(name, hw_config);

        /*
         * Assuming that a sound card is Sound Blaster (compatible) is the most common
         * configuration error and the mother of all problems. Usually sound cards
         * emulate SB Pro but in addition they have a 16 bit native mode which should be
         * used in Unix. See Readme.cards for more information about configuring OSS/Free
         * properly.
         */
        if (devc->model <= MDL_SBPRO)
        {
                if (devc->major == 3 && devc->minor != 1)       /* "True" SB Pro should have v3.1 (rare ones may have 3.2). */
                {
                        printk(KERN_INFO "This sound card may not be fully Sound Blaster Pro compatible.\n");
                        printk(KERN_INFO "In many cases there is another way to configure OSS so that\n");
                        printk(KERN_INFO "it works properly with OSS (for example in 16 bit mode).\n");
                        printk(KERN_INFO "Please ignore this message if you _really_ have a SB Pro.\n");
                }
                else if (!sb_be_quiet && devc->model == MDL_SBPRO)
                {
                        printk(KERN_INFO "SB DSP version is just %d.%02d which means that your card is\n", devc->major, devc->minor);
                        printk(KERN_INFO "several years old (8 bit only device) or alternatively the sound driver\n");
                        printk(KERN_INFO "is incorrectly configured.\n");
                }
        }
        hw_config->card_subtype = devc->model;
        hw_config->slots[0]=devc->dev;
        last_devc = devc;       /* For SB MPU detection */

        if (!(devc->caps & SB_NO_AUDIO) && devc->dma8 >= 0)
        {
                if (sound_alloc_dma(devc->dma8, "SoundBlaster8"))
                {
                        printk(KERN_WARNING "Sound Blaster: Can't allocate 8 bit DMA channel %d\n", devc->dma8);
                }
                if (devc->dma16 >= 0 && devc->dma16 != devc->dma8)
                {
                        if (sound_alloc_dma(devc->dma16, "SoundBlaster16"))
                                printk(KERN_WARNING "Sound Blaster:  can't allocate 16 bit DMA channel %d.\n", devc->dma16);
                }
                sb_audio_init(devc, name, owner);
                hw_config->slots[0]=devc->dev;
        }
        else
        {
                MDB(printk("Sound Blaster:  no audio devices found.\n"));
        }
        return 1;
}

/* if (sbmpu) below we allow mpu401 to manage the midi devs
   otherwise we have to unload them. (Andrzej Krzysztofowicz) */
   
void sb_dsp_unload(struct address_info *hw_config, int sbmpu)
{
        sb_devc *devc;

        devc = audio_devs[hw_config->slots[0]]->devc;

        if (devc && devc->base == hw_config->io_base)
        {
                if ((devc->model & MDL_ESS) && devc->pcibase)
                        release_region(devc->pcibase, 8);

                release_region(devc->base, 16);

                if (!(devc->caps & SB_NO_AUDIO))
                {
                        sound_free_dma(devc->dma8);
                        if (devc->dma16 >= 0)
                                sound_free_dma(devc->dma16);
                }
                if (!(devc->caps & SB_NO_AUDIO && devc->caps & SB_NO_MIDI))
                {
                        if (devc->irq > 0)
                                free_irq(devc->irq, devc);

                        sb_mixer_unload(devc);
                        /* We don't have to do this bit any more the UART401 is its own
                                master  -- Krzysztof Halasa */
                        /* But we have to do it, if UART401 is not detected */
                        if (!sbmpu)
                                sound_unload_mididev(devc->my_mididev);
                        sound_unload_audiodev(devc->dev);
                }
                kfree(devc);
        }
        else
                release_region(hw_config->io_base, 16);

        kfree(detected_devc);
}

/*
 *      Mixer access routines
 *
 *      ES1887 modifications: some mixer registers reside in the
 *      range above 0xa0. These must be accessed in another way.
 */

void sb_setmixer(sb_devc * devc, unsigned int port, unsigned int value)
{
        unsigned long flags;

        if (devc->model == MDL_ESS) {
                ess_setmixer (devc, port, value);
                return;
        }

        spin_lock_irqsave(&devc->lock, flags);

        outb(((unsigned char) (port & 0xff)), MIXER_ADDR);
        udelay(20);
        outb(((unsigned char) (value & 0xff)), MIXER_DATA);
        udelay(20);

        spin_unlock_irqrestore(&devc->lock, flags);
}

unsigned int sb_getmixer(sb_devc * devc, unsigned int port)
{
        unsigned int val;
        unsigned long flags;

        if (devc->model == MDL_ESS) return ess_getmixer (devc, port);

        spin_lock_irqsave(&devc->lock, flags);

        outb(((unsigned char) (port & 0xff)), MIXER_ADDR);
        udelay(20);
        val = inb(MIXER_DATA);
        udelay(20);

        spin_unlock_irqrestore(&devc->lock, flags);

        return val;
}

void sb_chgmixer
        (sb_devc * devc, unsigned int reg, unsigned int mask, unsigned int val)
{
        int value;

        value = sb_getmixer(devc, reg);
        value = (value & ~mask) | (val & mask);
        sb_setmixer(devc, reg, value);
}

/*
 *      MPU401 MIDI initialization.
 */

static void smw_putmem(sb_devc * devc, int base, int addr, unsigned char val)
{
        unsigned long flags;

        spin_lock_irqsave(&jazz16_lock, flags);  /* NOT the SB card? */

        outb((addr & 0xff), base + 1);  /* Low address bits */
        outb((addr >> 8), base + 2);    /* High address bits */
        outb((val), base);      /* Data */

        spin_unlock_irqrestore(&jazz16_lock, flags);
}

static unsigned char smw_getmem(sb_devc * devc, int base, int addr)
{
        unsigned long flags;
        unsigned char val;

        spin_lock_irqsave(&jazz16_lock, flags);  /* NOT the SB card? */

        outb((addr & 0xff), base + 1);  /* Low address bits */
        outb((addr >> 8), base + 2);    /* High address bits */
        val = inb(base);        /* Data */

        spin_unlock_irqrestore(&jazz16_lock, flags);
        return val;
}

static int smw_midi_init(sb_devc * devc, struct address_info *hw_config)
{
        int mpu_base = hw_config->io_base;
        int mp_base = mpu_base + 4;             /* Microcontroller base */
        int i;
        unsigned char control;


        /*
         *  Reset the microcontroller so that the RAM can be accessed
         */

        control = inb(mpu_base + 7);
        outb((control | 3), mpu_base + 7);      /* Set last two bits to 1 (?) */
        outb(((control & 0xfe) | 2), mpu_base + 7);     /* xxxxxxx0 resets the mc */

        mdelay(3);      /* Wait at least 1ms */

        outb((control & 0xfc), mpu_base + 7);   /* xxxxxx00 enables RAM */

        /*
         *  Detect microcontroller by probing the 8k RAM area
         */
        smw_putmem(devc, mp_base, 0, 0x00);
        smw_putmem(devc, mp_base, 1, 0xff);
        udelay(10);

        if (smw_getmem(devc, mp_base, 0) != 0x00 || smw_getmem(devc, mp_base, 1) != 0xff)
        {
                DDB(printk("SM Wave: No microcontroller RAM detected (%02x, %02x)\n", smw_getmem(devc, mp_base, 0), smw_getmem(devc, mp_base, 1)));
                return 0;       /* No RAM */
        }
        /*
         *  There is RAM so assume it's really a SM Wave
         */

        devc->model = MDL_SMW;
        smw_mixer_init(devc);

#ifdef MODULE
        if (!smw_ucode)
        {
                smw_ucodeLen = mod_firmware_load("/etc/sound/midi0001.bin", (void *) &smw_ucode);
                smw_free = smw_ucode;
        }
#endif
        if (smw_ucodeLen > 0)
        {
                if (smw_ucodeLen != 8192)
                {
                        printk(KERN_ERR "SM Wave: Invalid microcode (MIDI0001.BIN) length\n");
                        return 1;
                }
                /*
                 *  Download microcode
                 */

                for (i = 0; i < 8192; i++)
                        smw_putmem(devc, mp_base, i, smw_ucode[i]);

                /*
                 *  Verify microcode
                 */

                for (i = 0; i < 8192; i++)
                        if (smw_getmem(devc, mp_base, i) != smw_ucode[i])
                        {
                                printk(KERN_ERR "SM Wave: Microcode verification failed\n");
                                return 0;
                        }
        }
        control = 0;
#ifdef SMW_SCSI_IRQ
        /*
         * Set the SCSI interrupt (IRQ2/9, IRQ3 or IRQ10). The SCSI interrupt
         * is disabled by default.
         *
         * FIXME - make this a module option
         *
         * BTW the Zilog 5380 SCSI controller is located at MPU base + 0x10.
         */
        {
                static unsigned char scsi_irq_bits[] = {
                        0, 0, 3, 1, 0, 0, 0, 0, 0, 3, 2, 0, 0, 0, 0, 0
                };
                control |= scsi_irq_bits[SMW_SCSI_IRQ] << 6;
        }
#endif

#ifdef SMW_OPL4_ENABLE
        /*
         *  Make the OPL4 chip visible on the PC bus at 0x380.
         *
         *  There is no need to enable this feature since this driver
         *  doesn't support OPL4 yet. Also there is no RAM in SM Wave so
         *  enabling OPL4 is pretty useless.
         */
        control |= 0x10;        /* Uses IRQ12 if bit 0x20 == 0 */
        /* control |= 0x20;      Uncomment this if you want to use IRQ7 */
#endif
        outb((control | 0x03), mpu_base + 7);   /* xxxxxx11 restarts */
        hw_config->name = "SoundMan Wave";
        return 1;
}

static int init_Jazz16_midi(sb_devc * devc, struct address_info *hw_config)
{
        int mpu_base = hw_config->io_base;
        int sb_base = devc->base;
        int irq = hw_config->irq;

        unsigned char bits = 0;
        unsigned long flags;

        if (irq < 0)
                irq *= -1;

        if (irq < 1 || irq > 15 ||
            jazz_irq_bits[irq] == 0)
        {
                printk(KERN_ERR "Jazz16: Invalid MIDI interrupt (IRQ%d)\n", irq);
                return 0;
        }
        switch (sb_base)
        {
                case 0x220:
                        bits = 1;
                        break;
                case 0x240:
                        bits = 2;
                        break;
                case 0x260:
                        bits = 3;
                        break;
                default:
                        return 0;
        }
        bits = jazz16_bits = bits << 5;
        switch (mpu_base)
        {
                case 0x310:
                        bits |= 1;
                        break;
                case 0x320:
                        bits |= 2;
                        break;
                case 0x330:
                        bits |= 3;
                        break;
                default:
                        printk(KERN_ERR "Jazz16: Invalid MIDI I/O port %x\n", mpu_base);
                        return 0;
        }
        /*
         *      Magic wake up sequence by writing to 0x201 (aka Joystick port)
         */
        spin_lock_irqsave(&jazz16_lock, flags);
        outb(0xAF, 0x201);
        outb(0x50, 0x201);
        outb(bits, 0x201);
        spin_unlock_irqrestore(&jazz16_lock, flags);

        hw_config->name = "Jazz16";
        smw_midi_init(devc, hw_config);

        if (!sb_dsp_command(devc, 0xfb))
                return 0;

        if (!sb_dsp_command(devc, jazz_dma_bits[devc->dma8] |
                            (jazz_dma_bits[devc->dma16] << 4)))
                return 0;

        if (!sb_dsp_command(devc, jazz_irq_bits[devc->irq] |
                            (jazz_irq_bits[irq] << 4)))
                return 0;

        return 1;
}

int probe_sbmpu(struct address_info *hw_config, struct module *owner)
{
        sb_devc *devc = last_devc;
        int ret;

        if (last_devc == NULL)
                return 0;

        last_devc = NULL;

        if (hw_config->io_base <= 0)
        {
                /* The real vibra16 is fine about this, but we have to go
                   wipe up after Cyrix again */
                           
                if(devc->model == MDL_SB16 && devc->minor >= 12)
                {
                        unsigned char   bits = sb_getmixer(devc, 0x84) & ~0x06;
                        sb_setmixer(devc, 0x84, bits | 0x02);           /* Disable MPU */
                }
                return 0;
        }

#if defined(CONFIG_SOUND_MPU401)
        if (devc->model == MDL_ESS)
        {
                struct resource *ports;
                ports = request_region(hw_config->io_base, 2, "mpu401");
                if (!ports) {
                        printk(KERN_ERR "sbmpu: I/O port conflict (%x)\n", hw_config->io_base);
                        return 0;
                }
                if (!ess_midi_init(devc, hw_config)) {
                        release_region(hw_config->io_base, 2);
                        return 0;
                }
                hw_config->name = "ESS1xxx MPU";
                devc->midi_irq_cookie = NULL;
                if (!probe_mpu401(hw_config, ports)) {
                        release_region(hw_config->io_base, 2);
                        return 0;
                }
                attach_mpu401(hw_config, owner);
                if (last_sb->irq == -hw_config->irq)
                        last_sb->midi_irq_cookie =
                                (void *)(long) hw_config->slots[1];
                return 1;
        }
#endif

        switch (devc->model)
        {
                case MDL_SB16:
                        if (hw_config->io_base != 0x300 && hw_config->io_base != 0x330)
                        {
                                printk(KERN_ERR "SB16: Invalid MIDI port %x\n", hw_config->io_base);
                                return 0;
                        }
                        hw_config->name = "Sound Blaster 16";
                        if (hw_config->irq < 3 || hw_config->irq == devc->irq)
                                hw_config->irq = -devc->irq;
                        if (devc->minor > 12)           /* What is Vibra's version??? */
                                sb16_set_mpu_port(devc, hw_config);
                        break;

                case MDL_JAZZ:
                        if (hw_config->irq < 3 || hw_config->irq == devc->irq)
                                hw_config->irq = -devc->irq;
                        if (!init_Jazz16_midi(devc, hw_config))
                                return 0;
                        break;

                case MDL_YMPCI:
                        hw_config->name = "Yamaha PCI Legacy";
                        printk("Yamaha PCI legacy UART401 check.\n");
                        break;
                default:
                        return 0;
        }
        
        ret = probe_uart401(hw_config, owner);
        if (ret)
                last_sb->midi_irq_cookie=midi_devs[hw_config->slots[4]]->devc;
        return ret;
}

void unload_sbmpu(struct address_info *hw_config)
{
#if defined(CONFIG_SOUND_MPU401)
        if (!strcmp (hw_config->name, "ESS1xxx MPU")) {
                unload_mpu401(hw_config);
                return;
        }
#endif
        unload_uart401(hw_config);
}

EXPORT_SYMBOL(sb_dsp_init);
EXPORT_SYMBOL(sb_dsp_detect);
EXPORT_SYMBOL(sb_dsp_unload);
EXPORT_SYMBOL(sb_be_quiet);
EXPORT_SYMBOL(probe_sbmpu);
EXPORT_SYMBOL(unload_sbmpu);
EXPORT_SYMBOL(smw_free);
MODULE_LICENSE("GPL");

/* [<][>][^][v][top][bottom][index][help] */

[funini.com] -> [kei@sodan] -> Kernel Reading